Oxygen-3 / Oxygen-3 Plus Firmware Release Notes
Version 5.1.0 01/2018
New
- Added MAC-based whitelist feature to WiFi captive portal
- Added VLAN uplink failover capability
- Added QoS option for voice traffic (DSCP = 46)
- Added optional support for Telit LM940 module (LTE Band 66 support)
- Syslog now supports to support TLS encrypted remote logging
- Added Layer-2 GRE tunneling feature
- DHCP server: added feature to specify arbitrary option to send to clients
- Added Proxy / Redirect feature for client pings to reduce WWAN traffic
Changes
- Allow limited DHCP ranges for WiFi captive portal
- SNMP MIB file enhancements and cleanup
- Default configuration now leaves WiFi/LAN bridging disabled
- Linux kernel upgrade to version 4.9
- WWAN dialer now sets PDP context before checking for registration (decreases connection setup delay)
- Added session ID mechanism to web GUI
- Always auto-initate IPsec P2 SAs when tunnel(s) get established
- Update status in GUI more quickly when switching from CA to non-CA mode
Fixes
- Reset monthly Tx/Rx byte counter even if device was turned off on reset date
- IPsec: ensure that data for local subnets is never routed across tunnel, even if networks overlap
- Fixed reboot bug when applying failsafe configuration
Version 5.0.6 11/22/2017
New
- Show WWAN Cell-ID on web GUI overview screen
Changes
- Set default WWAN MTU to 1428
- Adjusting TCP MSS to 1388
Fixes
- Allow more time for retrieving ICCID from SIM
- Fixed occasional RSRQ reporting glitch
- IPsec web GUI fix to accept SHA256/384/512 P2 config values
- Linux kernel usbnet bugfix for incoming packets larger than configured WWAN MTU
- Fix: allow traffic between bridge interfaces
Version 5.0.2 07/14/2017
New
- Added support for Oxygen-3 Plus (uses Cat.6 LTE modem, Gig-Ethernet interface)
- Added QOS for routing protocols
- Added authentication option to 'ssh to serial port' feature
- Added VLAN trunk support (up to 4 VLANs)
- IPsec: added support for multiple local encrypted networks
- Added feature to route all incoming GRE traffic to LAN
- Added 'celltool' CLI script for extended WWAN modem debugging
Changes
- Dropped obsolete ciphers and added more modern ones to HTTPS web GUI
- Now using a more secure 3072 bit RSA certificate for HTTPS
- Linux kernel upgrade to 4.4
- Improved internal WWAN connection manager (dialer) architecture
- Detect O3 hardware revision (now part of version string)
- Improved WCDMA and LTE band selection to make it much more flexible and allow multi-band
- Changed default status logging interval to 15 minutes
- Misc. SNMP fixes and enhancements
Fixes
- Bugfix: GUI-based SNAT/DNAT rules will be added on top so that they always take precedence
- Properly display USB port info on 'System Status' web gui page
- Fixed SNMP MIB cypGwCpeState up/down reversal
- Bugfix: don't send CPE up/down trap when SNMP daemon (re-)starts
Version 4.9.0 12/7/2016
New
- Added direct SSH-to-serial-port feature
- Added 'oxycom' serial console CLI script
- Added GRE tunnel feature
- Added feature to obtain (local-) time from cellular network
- Added feature to run an NTP server on the Oxygen to provide time to attached devices
Changes
- Added syslog entries to track reversal to default or failsafe config
- Added syslog entry to track DC power being applied to the O3
- NAT: perform 'endpoint independant NAT mapping' whenever possible
- Enabled proxy-ARP by default
Fixes
- Cell module: implemented workaround for obscure DHCP netmask bug
- Fixed SNMP process not staying up if captive portal is enabled and SNMP config is changed
- Fix: 'reset to factory default' now also resets radio-connected/disconnected script
Version 4.8.1 08/11/2016
New
Changes
Fixes
- fixed SSH/RADIUS regression bug that was present since 4.6.x
Version 4.8.0 08/10/2016
New
- Added option to select scope of NAT (LAN or everything)
Changes
- DHCP lease time now adjustable from 2 min. to 1 week
- Increased IPsec window size from 4 to 16 to improve Cisco ASA interoperability
- Improved IPsec DPD processing to enhance Cisco ASA interoperability
Fixes
- Fix to correctly block all outgoing packets with wrong source IP
- ccm-client bugfix to resolve sudden process restart
Version 4.7.3 05/31/2016
New
- Added support for external RS232 serial port connector
Changes
Fixes
- Fixed ccm-client to prevent lock-ups
Version 4.7.0 05/13/2016
New
- Added SNMPv3 support
- Added WWAN SIM PIN support
Changes
- Minor changes to factory default config
- Block SNMP traffic on LAN network- and broadcast addresses
Fixes
- Fixed local DNS which was not working when set to static DNS IPs with no DHCP
Last modified 5 days ago
Last modified on 01/17/18 15:26:03