A

• accel altvalidmax: set maximum allowable change in altitude before GPS module is reset
• accel cond: set acceleration trigger condition
• accel gpscoef: set minimum GPS vs accelerometer or OBD speed based acceleration required
• accel gpsobddiff: set maximum allowable difference between GPS and OBD speed to prevent accel gpsmaxspeed and accel validmax checks
• accel history: enable/disable historical GPS&OBD report used for acceleration calculation
• accel historydelay: set delay between each historical GPS&OBD report
• accel historynum: set number of historical GPS&OBD report to generate
• accel maxgpsspeed: set maximum allowable GPS speed before GPS module is reset
• accel report: set acceleration report
• accel rollcond: set rollover trigger condition
• accel rollrep: set rollover report
• accel sensor: set sensor used for triggering longitudinal acceleration
• accel validmax: set maximum allowable GPS acceleration before GPS module is reset

• access autologin: set auto-login on serial console
• access password: set login password for SSH, Telnet, Web, Console
• access sessiontimeout: session timeout value
• access cell ftpport: configure FTP port on Cellular interface
• access cell httpsport: configure HTTPS port on Cellular interface
• access cell sshport: configure SSH port on Cellular interface
• access cell telnetport: configure Telnet port on Cellular interface
• access cell webport: configure HTTP (Web) port on Cellular interface
• access lan0 ftpport : configure FTP port on LAN0 interface
• access lan0 httpsport : configure HTTPS port on LAN0 interface
• access lan0 sshport : configure SSH port on LAN0 interface
• access lan0 telnetport : configure Telnet port on LAN0 interface
• access lan0 webport : configure HTTP (Web) port on LAN0 interface
• access lan1 ftpport : configure FTP port on LAN1 interface
• access lan1 httpsport : configure HTTPS port on LAN1 interface
• access lan1 sshport : configure SSH port on LAN1 interface
• access lan1 telnetport : configure Telnet port on LAN1 interface
• access lan1 webport : configure HTTP (Web) port on LAN1 interface
• access wlan ftpport : configure FTP port on WLAN interface
• access wlan httpsport : configure HTTPS port on WLAN interface
• access wlan sshport : configure SSH port on WLAN interface
• access wlan telnetport : configure Telnet port on WLAN interface
• access wlan webport : configure HTTP (Web) port on WLAN interface

• agpspde :configure Assisted GPS (A-GPS) using cellular device location based features
• apn :set carrier access-point name
• authport :set the port number for a Radius authentication server
• authsecret :set the shared secret for a Radius authentication server
• authserver :set the IP address for a Radius authentication server
• autoconnect :auto network connection
• autopevent :turns on $PEVENT message reporting of trigger/event description

• aux ack :sets the ack character sequence for mode 24
• aux authtype :sets the authentication mechanism used with auxiliary device
• aux checksum :sets the value used for checksum calculation
• aux cond :sets the triggering conditions for mode 23/24
• aux conf :sets the reporting configuration for mode 23/24
• aux datatype :sets the data type of the auxiliary device payload
• aux dev :sets the auxiliary device name for mode 23/24 (same as aux polldev)
• aux lead :sets the leading characters for mode 24
• aux leadlen :sets the number of leading characters for mode 24
• aux lead2 :sets the secondary set of leading characters for mode 24
• aux lead2len :sets the number of characters in the secondary set for mode 24
• aux leadmode :sets the leading characters matching criteria for mode 24
• aux leadterm :set to use leading or terminating characters or both for mode 24
• aux len :sets the payload length for mode 23/24 (same as aux pollen)
• aux mode :sets the specific processing method for mode 24
• aux pollnow :tells CTM to poll the auxiliary device for mode 23
• aux pollstr :sets the polling string for mode 23
• aux polltim :sets the polling timeout for mode 23
• aux repmode :sets whether to append payload to ASCII (msg 114) or binary (msg 112) header
• aux report :sets the reports to be used for mode 22-24
• aux rmleadterm :set to remove leading or terminating characters or both for mode 24
• aux term :sets the termination characters for mode 22/24
• aux termlen :sets the number of termination characters for mode 22/24
• aux timeoutsend :sets whether data is sent out when serial input times out for mode 22/24

B

• boomreport :set the boom tracker report(s)

• bt console :enable/disable Bluetooth console mode
• bt enable :enable/disable all Bluetooth functions
• bt ble :enable/disable scanning Bluetooth Low Energy
• bt blemax :set the maximum number of BLE devices being tracked
• bt blestale :sets when each BLE data is considered stale and to be removed
• bt ip :set the local IP for Bluetooth NAP
• bt name :set the local Bluetooth device name
• bt pin :set the local Bluetooth device password
• bt nap :enable/disable Bluetooth NAP mode
• bt obd :enable/disable Bluetooth OBD mode
• bt remname :set the remote Bluetooth device name
• bt rempin :set the remote Bluetooth device password

C

• can apply :set STM with values set in cmd engparam and can prot
• can baud :set CAN baud rate
• can enghours :set source of engine hour data
• can engparam :set which parameters are to be queried/reported
• can errmax :set number of sessions with CAN errors when CAN is no longer attempted
• can odometer :set source of odometer data
• can psthruid :set CAN header/ID to look for by canpsthru ps
• can psthrumin :set minimum time for each CAN header/ID passed by canpsthru ps
• can prot :enable/disable internal CAN and sets the protocol
• can qryrate :set the maximum OBD querying rate
• can senddiag :set how often diagnostic session is requested
• can showdata :shows a list of unique received CAN data
• can std :set CAN header type
• can subsys :set CAN subsystems to use
• can usbprot :set the USB CAN protocol
• can vtype :set the specific vehicle to be used with CTM

• cardlistclear :erase approved ID list from device
• cardlistload :load approved ID list for swipe card interface
• cardlistsave :process approved ID list for use by CTM and save to NV-RAM
• cardunlockload :load a swipe card unlock script to the device

• ccm-client enable :enable Cypress Cloud Manager (CCM) support
• ccm-client interval :set CCM client check-in interval
• ccm-client server :set CCM server IP address or hostname
• ccm-client port :set CCM server port
• ccm-client ssl :enable/disable SSL encryption for CCM client/server communication
• ccm-client accept-untrusted :allow/disallow untrusted CCM server certficates
• ccm-client netname :set CCM network name identifier
• ccm-client ack :send acknowledgement message to CCM server
• ccm-client check-in :initiate immediate CCM check-in

• cportal enable :enable captive portal
• cportal nasid :set captive portal NAS ID
• cportal uamport :set UAM port
• cportal radserver1 :set RADIUS server 1 address
• cportal radserver2 :set RADIUS server 2 address
• cportal authservurl :set authentication server URL
• cportal uamsecret :set UAM secret
• cportal radsecret :set RADIUS secret
• cportal radauthport :set RADIUS authentication port
• cportal radaccport :set RADIUS accounting port
• cportal whitelist :set whitelist
• cportal domains :set domains (dynamic whitelist)
• cportal sessiontimeout :set session timeout
• cportal idletimeout :set idle timeout
• cportal bwdown :set download bandwidth
• cportal bwup :set upload bandwidth

• clientmac :set client mac address for modem mode with DHCP
• confdrop :drop a backup configuration onto a CTM-200
• confupgrade :configures the device for automatic configuration capability
• ctm15x :command for configuration of protected values

D

• data :query count of data transmitted/received over wireless link
• datacond :wireless link total data count trigger condition
• datareport :set the link data report(s)

• device cell :configure cell device
• device cellmtu :configure MTU for the cellular interface
• device cellnetwork :configure cell device to use a specified network type
• device lteband :configure cell device to use a specified LTE band
• device priority :define device priority for Cell + Wifi client configurations
• device wifi :configure Wifi device

• dir :set NAM phone number,MDN,MIN
• dmz :demilitarized zone (DMZ) feature
• dnscheck :check valid DNS
• dout :set/query digital outputs
• doutrestore :set which digital outputs are restored on boot
• dyndns :dynamic DNS
• dynhost enable :enable/disable local DNS lookup
• dynhost set :configure local DNS lookup

E

• emailsrv :set email server
• enghours :calculate engine hours
• enghrmode :used to configure enghours command
• esn :query the serial number (ESN/IMEI) of the wireless device
• ethernet :enable or disable ethernet services

• event add :manually add events to the event log
• event dump :dump the event log file
• event healthinterval :interval between HEALTH status events
• event logclear :clear the event log file
• event loglevel :set the event reporting level
• event minoffline :set minimum time interval before reporting CELL_ONLINE event
• event report :set which type of report to use for event reports

F

• firewall :configure firewall – port forwarding
• freeconsole :kill serial console prompt
• friends :set firewall friends list
• ftp server :enable/disable ftp server

• fuel dev :set the maximum allowable standard deviation for fuel level
• fuel io :configure GPIO for fuel calculation
• fuel maxspd :set the maximum speed to use fuel level
• fuel mode :set the fuel mode
• fuel query :query the total fuel value
• fuel rate :set the fuel rate distance for fuel rate calculation
• fuel rate query :query the fuel rate
• fuel rate reset :reset the fuel rate
• fuel refuel :set the percent fuel increase to consider refueling has occurred
• fuel reset :reset the total fuel value
• fuel tank :configure fuel tank size and reading settings

G

• geort acount :view Geo-Route allowed zone violation counter
• geort c2bin :convert Geo-Route route lists into CTM200 format
• geort delete :delete (deactivate) Geo-Routes
• geort enable :enable/disable Geo-Route
• geort list :view routes being checked by Geo-Route
• geort period :set how often Geo-Route checks for violation[
• geort rcount :view Geo-Route restricted zone violation counter
• geort report :set reports used for Geo-Route
• geort th :set Geo-Route violation threshold
• geort update :add/update (activate) Geo-Routes

• gopad :enable either 1 or 2 instances of PAD
• gpsaccel :GPS report trigger for hard acceleration and deceleration events
• gpsaddmes :add GPS messages to a report
• gpscache :enable using cached GPS position
• gpscond :GPS report trigger conditions
• gpsdata :display status of GPS input devices
• gpsdelmes :delete GPS message
• gpsdgps :enable DGPS mode and SBAS
• gpsdop :set GPS DOP filtering
• gpsemail :GPS email address
• gpsgga :GPS GGA message
• gpsinput :GPS input device, internal on board GPS module, external GPS device or Cellular based A-GPS
• gpslocip :GPS local IP address/domain name
• gpslocport :GPS local port
• gpsmes :GPS messages
• gpsparam :GPS port configuration and priority
• gpspos :set fixed GPS position
• gpsremip :GPS remote IP address/domain name
• gpsremport :GPS remote port
• gpsrep :GPS reporting
• gpsrmc :GPS RMC message
• gpssms :set destination of GPS SMS report
• gpstime :set priority of valid GPS as system time synchronization source

H

• No commands

I

• idle cond :set the idle condtion
• idle mode :set the idle mode
• idle query :query the idle time
• idle report :set report for idle conditon
• idle reset :reset the idle time
• idle time :set the idle time

• igncond :ignition report trigger conditions
• ignreport :set ignition trigger report

• input :query input channels status
• insetup :input setup
• installer id :installer id
• installer name :installer name
• installer vueserver :installer GPS server address
• installer vuereportnum :installer GPS server report number
• ioaddmes :add IO message
• iocond :IO report trigger conditions
• iodelmes :delete IO message
• ioemail :IO email address
• iolocip :IO local IP address/domain name
• iolocport :IO local port
• iomes :IO messages
• ioremip :IO remote IP address/domain name
• ioremport :IO remote port
• iorep :IO reporting
• iosms :set destination of IO SMS report
• ipadr :query WWAN IP address

• iot mqtt_enable :enable MQTT/IoT reporting
• iot azure connection_string : set Microsoft Azure device connection string
• iot watson auth_token :set Watson IoT device authentication token
• iot watson orgid :set Watson IoT organization ID
• iot watson mode :set Watson IoT data report mode

• ipsec :show all IPsec commands
• ipsec dpddelay :set DPD (Dead Peer Detection) delay time
• ipsec dpdmaxfail :set DPD max fail count
• ipsec dpdretry :set number of DPD retries
• ipsec enable :enable/disable IPsec
• ipsec ikeauth :set IPsec Phase 1 authentication type
• ipsec ikedhgroup :set IPsec Phase 1 Diffie-Hellman group
• ipsec ikeenc :set IPsec Phase 1 encryption algorithm
• ipsec ikeexchange :set IPsec Phase 1 exchange mode
• ipsec ikehash :set IPsec IKE Phase 1 hash algorithm
• ipsec ikeinitial :set IPsec Phase 1 initial contact setting
• ipsec ikelifetime :set IPsec Phase 1 lifetime
• ipsec ikemodecfg
• ipsec ikemyid :set IPsec Phase 1 Local ID
• ipsec ikepassive :set IPsec Phase 1 peer role - initiator/responder
• ipsec ikepeerid :set IPsec Phase 1 Remote ID
• ipsec ikeproposal :set IPsec Phase 1 Proposal
• ipsec ikerekey :set IPsec Phase 1 DPD rekey policy
• ipsec ikeverifyid :verify Remote ID
• ipsec localnet :set whether to use LAN0 or LAN1 for IPsec subnet
• ipsec loglevel :set IPsec log level
• ipsec natt :enable IPsec NAT traversal
• ipsec nattkeepalive :set NATT keepalive interval
• ipsec psk :set IPsec pre-shared key
• ipsec remgw :set IPsec remote gateway IP address
• ipsec remnet :define IPsec remote subnet(s)
• ipsec remping :set ping interval to remote tunnel target
• ipsec remtarget :set IP address of remote target
• ipsec restrict :define restrictive access policy
• ipsec saauth :define IPsec ISAKMP phase II authentication algorithm
• ipsec saenc :define IPsec ISAKMP phase II encryption algorithm
• ipsec salifetime :define IPsec ISAKMP phase II lifetime
• ipsec sapfsgroup :define IPsec ISAKMP phase II perfect forward secrecy group
• ipsec show :show IPsec configuration
• ipsec split :enable/disable split tunneling

J

• No commands

K

• No commands

L

• lan8021x :set 802.1x LAN authentication
• lanbridge :Bridge LAN ethernet interfaces
• landhcp :LAN DHCP server settings
• lanfriends :control ethernet access control using MAC addresses.
• langw :LAN Gateway IP address
• lanip :IP address of device on LAN
• lanmtu :MTU of LAN interface
• lannat :Enable SNAT on LAN interface
• lannetmask :Netmask of device on LAN
• lanproto :Set interface prototype to static or dhcp
• lanrepip :LAN IP address for local reporting
• lanwd :Enable/disable LAN Watchdog

M

• mbusm add :add MODBUS slave in MODBUS master mode
• mbusm cond :sets reporting conditions for MODBUS master mode
• mbusm data :shows current MODBUS slave register values for MODBUS master mode
• mbusm del :remove MODBUS slave in MODBUS master mode
• mbusm exccond :sets condition to trigger MODBUS exception reports for MODBUS master mode
• mbusm excreport :sets reports to be used for MODBUS exception triggered reports
• mbusm poll :sets polling MODBUS slaves while in MODBUS master mode
• mbusm report :sets reports to be used for MODBUS master triggered reports

• mip :mobile IP

• modbusadd :add a MODBUS TCP slave, serial slave or self slave, query MODBUS slave gateway list
• modbusctm130 :enable backward compatibility with CTM-13X MODBUS messages over-the-air
• modbusdel :delete MODBUS entry
• modbusgw :manual MODBUS gateway initiation
• modbusidmap :set up MODBUS ID to device IP:port map
• modbusmode :sets the MODBUS gateway mode
• modbusport :sets the MODBUS port number
• modbussecure :secure MODBUS for use with SSH tunneling

• mode :sets serial port(s) connection mode
• modemid :assign device ID
• modemmode :enable modem Mode/Half Bridge mode
• modemmodedhcp :enable DHCP support with Modem Mode

• msgredirect add :add a redirect IP address/port
• msgredirect del :delete a redirect IP address/port
• msgredirect enable :enable/disable message redirect application
• msgredirect list :list redirect entries
• msgredirect port :configure message redirect listening port
• msgredirect remip :restrict incoming redirect messages to a specified remote source IP

• multiwan enable :enable multiwan configuration
• multiwan mode :select multiwan mode type

N

• net dnssource :sets permitted sources from which to accept DNS server IP addresses
• net staticdns :define static DNS server IP addresses
• netwd :network watchdog
• networktime :set priority of cellular network time as system time synchronization source.
• nmeamode :set NMEA 0183 version for GPGLL and GPRMC sentences
• ntpserver :set URL or IP of NTP server for system time synchronization
• ntptime :set priority of NTP client as system time synchronization source

O

• obdcond :OBD report trigger conditions
• obddata :display data obtained from OBDII transmitter
• obdlistload :load parameter list used by pobdx
• obdreport :set report for OBD trigger
• obdsp :sets protocol used by OBDII transmitter
• odometer :GPS odometer
• orientation :set device mounting orientation for use with accelerometer sensor
• otasp :Over-The-Air Service Provisioning

P

• pad :PAD configuration
• pad clientport :PAD client port number for dialup emulation modes
• pad echo :PAD echo mode
• pad esc :PAD escape sequence
• pad esct :PAD escape guard time
• pad fifo :PAD fifo
• pad fwdc :PAD forwarding character
• pad fwdl :PAD forwarding length
• pad fwdt :PAD forwarding time
• pad ip :PAD IP address
• pad mode :PAD mode
• pad pfc :PAD postfix character
• pad port :PAD port number
• pad reset :PAD reset
• pad secure :Secure PAD server for use with SSH tunneling
• pad svct :PAD server connection cut-off timer

• panicreport :set pendant panic report
• panicreportack :set device to send pendant acknowledgment when panic report received
• panicreptype :set pendant report
• pendantreport :set pendant panic report type

• pcyp key :pcyp key
• pcyp key view :view pcyp keys

• pcyp delimiter :pcyp delimiter

• pcyp msg :pcyp msg
• pcyp msg add :add a key to a pcyp msg
• pcyp msg del :del a pcyp msg or a key within a pcyp msg
• pcyp msg view :view pcyp msg keys
• pcyp msg replace :replace a key in a pcyp msg
• pcyp msg query :query pcyp msgs

• pin :set 4-digit SIM card PIN code for cell devices
• ping :pings a specific IP address
• pobda-pobdh :configure OBDII reports
• port :serial port settings
• ppp :local Point to Point Protocol connection
• pswd :sets password used for wireless network access via simple IP

• pulse coef :set the pulse rate coefficient multiplier
• pulse edge :set whether pulse counting uses edge detection or voltage threshold
• pulse input :set voltage threshold for pulse counting
• pulse period :set whether pulse rate is to be calculated
• pulse pwm :enable/disable PWM detection

• pupcond :power up report trigger conditions
• pupreport :set power up report

• pwr accelt :accelerometer/acceleration threshold
• pwr geofence :geofence threshold
• pwr mode :power mode
• pwr rtc :RTC (real-time clock) threshold
• pwr sdwn :power shutdown
• pwr speedth :GPS speed threshold
• pwr temp :temperature threshold
• pwr vcct :supply voltage threshold
• pwr woe :power wake on event

Q

• No commands

R

• ratesel :Rate select for Sierra Wireless CDMA/EVDO data devices/modules only
• ratetmr :Rate Timer, Sierra Wireless CDMA/EVDO only ?
• repaddmes :add messages to a report configuration, display report configuration messages
• repdelmes :delete messages from a report configuration
• repemail :configure report email address

• repfiledelivery :configure delivery parameters for file-based reporting
• repfiledir :configure main folder for file-based reporting
• repfilename :configure filename for file-based reporting
• repfileout :configure outbox folder for file-based reporting
• repfilesize :configure maximum file size for file-based reporting
• repfiletimestamp :configure timestamp added to data files for file-based reporting
• repfilezip :configure compression of data files for file-based reporting

• replocip :configure report local IP address/domain name
• replocport :configure report local port
• reportscripts :configure custom scripts to be triggered when reports are generated
• repremip :configure report remote IP address/domain name
• repremport :configure report remote port
• repsms :configure report SMS address
• reptype :configure local and remote report types, store-and-forward
• rfstats :Displays various RF statistics
• rfswitch :enable/disable RF switch
• rmtd :reverse telnet connection
• rssi :RF signal strength

S

• saltreport :set salt-spreader report
• sat enable :set satellite mode
• sat force :force satellite to be enabled in dynamic mode when Pendant PANIC messages are sent
• sat flush :clears outbound satellite messages
• sat ip :set the remote server IP to send received sat msgs that are not $cmd msgs to
• sat mt :minimum time between identical report numbers when using satellite
• sat port :set the remove server port to send received sat msgs that are not $cmd msgs to
• sat pwr :enable/disable satellite when satellite is in dynamic mode
• sat reset :clears the satellite tx/rx info
• sat stats :show satellite status

• satbackup :switch to backup satellite modem
• save :saves configuration
• sendreport :generates and sends a "One-Shot" report upon execution of the command
• showconfig :displays current configuration settings
• showstate :displays device state
• sms enable :SMS configuration access
• sms fwdreport :configure forwarding of incoming SMS messages
• sms friends :set friends list for SMS commands
• snfdelay :store and Forward delay period before SNF starts
• snfflush :store and Forward Flush
• snflog :store and Forward log
• snfonsd :configure SNF to use SD card storage

• snmp enable : Enable SNMP
• snmp rwcommunity : Set the RW community
• snmp rocommunity : Set the RO community
• snmp trapcommunity : Set the Trap community
• snmp traphost : Set the Trap IPv4 address
• snmp trapversion : Set the Trap version
• snmp v3user : Set the v3 user
• snmp v3access : Set the v3 user access
• snmp v3authpass : Set the v3 authentication passphrase
• snmp v3privpass : Set the v3 privacy passphrase
• snmp v3security : Set the v3 security
• snmp v3authtype : Set the v3 authorization type
• snmp v3privtype : Set tv3 privacy type
• snmp v3authfailtrap : Enable v3 authorization fail trap

• spc :service provisioning code
• speedth :speed threshold for enabling RF module of the device
• sshkey :generate a ssh key
• staticroute :configure static routes for packet routing
• stm upgrade :upgrades STM/Mini Micro FW

• swipe delay :set whether to look for valid RTC time before enabling iButton
• swipe gpio :set iButton GPIO mapping
• swipe idmode :set how user IDs are parsed by the system before being reported
• swipe idregex :set how the ID is parsed by the system to be reported
• swipe ignwindow :set time after ignition OFF before requiring another swipe
• swipe invoutmask :set which outputs are toggled when an invalid card is read
• swipe invoutval :set output values when an invalid card is read
• swipe mode :set swipe-card interface
• swipe readwindow :set time after boot to allow reading an ID
• swipe report :set swipe-card report
• swipe sameiddelay :set time between identical swipes before they are processed
• swipe valoutmask :set which outputs are toggled when a valid card is read
• swipe valoutval :set output values when a valid card is read
• sysdb get :query system database key/value data
• sysdb list :list descriptive info for system database keys
• syslog :system log

T

• taipchecksum :enable/disable checksum in TAIP messages
• taipid :set TAIP ID
• taipuseid :enable/disable reporting of ID in TAIP messages

• tcpframing :configure framing of report TCP packets
• tcppersist :set persistent TCP report connections

• tftp remote :enable/disable allow tftp remote access to the CTM
• tftp server :enable/disable tftp server

• timesync :set period for system time synchronization
• timezone :query/set system timezone

U

• univwd :configure universal watchdog
• univwdtimer :set universal watchdog timer interval
• upgradefw :upgrade firmware image
• upgradesrv :set authorized IP for remote admin
• user :sets username used for wireless network access via simple IP

V

• vcc :supply voltage
• vcccond :supply voltage level report trigger conditions
• vccreport :set supply voltage level report

• ver :firmware version

• vin clear :delete the recipes downloaded by the VIN lookup tool
• vin port :configure TCP port of repository
• vin pwrup :configure VIN lookup tool to run on power up
• vin query :manually execute the VIN lookup tool
• vin server :configure IP address of repository
• vin ssl :configure to use HTTPS or HTTP for accessing repository

• vpnc :enable VPNC

• vue ack :run the VUE client/server acknowledgement
• vue period :configure VUE client periodic check-in interval
• vue port :configure TCP server port for device
• vue pwrup :configure VUE client to run on power up
• vue remip :configure URL/IP address of remote VUE server
• vue remport :configure TCP port number of remote VUE server
• vue service :configure VUE server type or disable VUE client

W

• wifi ap|client channel: set the wireless channel
• wifi ap|client encryption: sets the wireless encryption type
• wifi ap|client hwmode: set the wireless hardware mode
• wifi ap ignorebcast: disable broadcast of AP SSID
• wifi ap isolate: isolate wifi clients from each other
• wifi ap|client key: set the wireless key
• wifi ap|client ssid: sets the wireless SSID
• wifi ap macaddrallowadd: add a MAC address to wifi allow list
• wifi ap macaddrallowdel: remove a MAC address from wifi allow list
• wifi ap macaddrdenyadd: add a MAC address to wifi deny list
• wifi ap macaddrdenydel: remove a MAC address to wifi deny list
• wifi client eap: wifi client EAP/TTLS support
• wifi country: set the wireless regulatory country code
• wifi mac: query the wireless MAC address
• wifi watchdog: configure wireless watchdog

• wlan bridge: bridge wifi Access Point with the LAN interface(s)
• wlan dhcp: configure WLAN DHCP address range
• wlan enable: configure dual-mode device for:cellular+wifi
• wlan gw: configure a default gateway IP address for the wifi client interface
• wlan ip: configure a static IP address for the wifi client interface
• wlan mtu: MTU of WLAN interface
• wlan netmask: configure the IP address netmask for the wifi client interface
• wlan proto: configure the network protocol for the wifi client interface

• wpan acktype: Man Down Pendant acknowledgement type
• wpan adddev: WPAN accessory add device id, query device id
• wpan delall: WPAN accessory delete all device ids
• wpan deldev: WPAN accessory delete device id
• wpan dist: configure WPAN Gateway distance report message
• wpan msgtermid
• wpan panid: WPAN accessory set PAN id, query PAN id
• wpan pensrv: WPAN server for remote access to Man Down Pendant devices
• wpan secure: secure WPAN server for use with SSH tunneling
• wpan stm: select internal gateway

X

• No commands

Y

• No commands

Z

• No commands